Machines to Cut, Bend, Strip, and Point Semi-Rigid Coax Cable

Machines to Cut, Bend, Strip, and Point Semi-Rigid Coax Cable

Winton offers a series of fabrication machines all designed to help fabricate semi-rigid coax cable.  Coax cable is a common means to transport high frequency signals in microwave communication systems. Coax cable can be found in commercial and military applications all over the world. Everything from cell phone towers to ship-to-ship satellite communication systems makes use of coax cable. Two common types of coax are semi-rigid coax cable and flexible coax cable. Cutting, stripping the ends, and bending coax are discussed below for both types of cable.

Choose a Category to See Our Machines

CNC Semi-Rigid Coax Benders CNC Semi-Rigid Coax Benders
Our semi-rigid coax benders are designed to make precision bends in semi-rigid cable.
CNC Semi-Rigid
Coax Benders
CNC Coax Cut-to-Length CNC Coax Cut-to-Length
Winton offers a benchtop cut-to-length automatic saw featuring a programmable part quantity and programmable cut length.
CNC Coax Cut-to-Length
Coax Hand Benders Coax Hand Benders
All coax hand benders are designed from quality components and are tested for quality assurance in house. Winton offers interchangeable production-ready tooling to bend the same tubular shape time and time again.
Coax Hand Benders
CNC Coax Stripper CNC Coax Stripper
Winton offers next generation semi-rigid coax stripper software. The new design features updated stripper heads allowing for more repeatable stripping of small diameter coax cable.
CNC Coax Stripper
Coax Pointer Machine Coax Pointer Machine
Winton’s coax pointer machine is designed to use a high speed motor coupled with precision cutters to insure an accurate point on the end of a center conductor in one seamless motion.
Coax Pointer Machine
Angle Measuring Machine Angle Measuring Machine
Winton offers Digital protractor designed to feature two arms to measure the bend angle of numerous bend configurations.
Angle Measuring Machine

Cutting Semi-Rigid Coax with a Saw 
Semi-rigid often comes in straight lengths. Cutting semi-rigid most often involves a saw type cut. A saw type cut is preferred because the next step in processing the coax involves dressing the ends for fittings. If the ends are not cut square and/or have too much burr on the outside diameter, the coax stripping machine may not accept the end of the semi-rigid cable for processing. 

The automatic feed & cut machine to the left clamps the coax cable on both sides of the cable during the cutting operation. Holding the cable secure as the saw blade cuts the coax is most important for making quality cuts. 

A thin high-speed saw will cut thru the semi-rigid cable with little trouble. The outer jacket of a typical piece of coax is copper or aluminum with a plastic insulator surrounding the center conductor. With the right number of teeth on the saw, production can proceed as long as the saw blade keeps a sharp edge. As the blade dulls the burr on the outside diameter tends to increase. 

The quality of cut is not the only QC feature to be concerned with. The repeatability of the cut length is most important. If the cut length varies too much, the VSWR will also vary. Selecting a cutting process that produces a square cut while at the same time cuts consistent lengths is most desirable.

Cutting Flexible Coax with a Saw System 
Flexible coax cable is becoming more prevalent in commercial systems. Being flexible, the application that the flexible cable is used in may determine if the cable gets bent by hand or by a CNC bending machine. Nevertheless, flexible cable, unlike semi-rigid cable, comes on a spool. Getting it from the spool, metered out and cut to precision lengths requires a cutting system that first straightens the cable. Once straightened, a saw type cut can be made. 

The picture to the left shows a system for processing flexible coax cable. The system automatically pulls the flexible coax off the spool, straightens it and then cuts it to a programmed length. 

The same saw blade that is used to cut semi-rigid coax can be used to cut flexible coax. Care must be taken to ensure that both sides of the cable are secured during the cutting process. Lack of support during the cutting process can lead to poor cutting results.

After the Cutoff – Stripping the Ends 
Once the cut lengths come off the saw with nice square ends, the ends of the cable can now be dressed for a connector. Dressing the ends may involve multi-step cuts in each end. One of the most important quality features of dressing the ends of a cable involve removing the outer jacket and insulator without nicking the inner conductor.

Making Production Quality Bends 
Consistent products shipped require consistent components. Thus the need to bend coax cable consistently. Consistent bending starts with a good set of bend tools. Bend tooling for coax cable involves a bend spool, clamp die, and a wipe roller. For CNC bending, a collet will be necessary. Bending coax by hand can yield the same results as bending via a CNC coax bender. The difference being that when bending by hand, the operator must remain focused in order to avoid quality problems down stream. 

To the left is a CAD rendering of a benchtop mounted CNC coax cable bender. The machine can bend semi-rigid or flexible coax with or without connectors installed. Most CNC coax cable benders have a capacity of .250” OD semi-rigid cable. 

When choosing a centerline bend radius, first review the literature from the manufacture of the coax cable. This is a good place to look for the minimum allowable bend radius. 

Flexible coax will hold its shape once bent to a certain extent. Flexible coax cable can not take the G forces that semi-rigid can and still hold its original shape. Nevertheless, flexible coax has its place in the market where cost of goods sold is often a concern. 

Quite often long lengths of semi-rigid coax are loaded into a bender for processing. These long lengths are managed thru the bending cycle using what is called hitch feed. The initial straight lengths can be longer than the bender itself. However, with hitch feed built into the software, the bender can advance the coax with ease. 

When bending semi rigid from a long stick, a cutoff saw is most often mounted onto the bender. After a specific configuration is bent, the cutoff saw mounted to the bender can be used to part the formed part from the long stick. 


Quality Concerns when Fabricating Coax 
Being able to bend semi-rigid cable or flexible coax cable consistently can impact the VSWR to some extent. Within the bend zone itself, additional surface defects such as dents on the outer jacket will influence the VSWR. Dents or defects in the straight sections between bends can also cause the VSWR to change. Dents or surface defects found in semi-rigid or flexible cable are often the result of manual labor oversights and are often attributable to the following: 
• Change in clamping pressure during the cutting and/or bending operation 
• Manual handling variations during the cutting and/or bending operation 

Cutting, stripping, and/or bending coax cable for industrial applications requires significant care during the fabrication process. A gentle touch coupled with consistent manufacturing processes can translate into quality coax cable assemblies destined for production. 

George Winton, P.E. designs and builds CNC tube bending equipment for Winton Machine in Suwanee, GA. He can be reached at or by phone at  888.321.1499. 

About the Machines We Build 
All coax cutters & benders are designed and tested in house. We use standard purchased components to build every machine. We at Winton are proud of the quality of every coax fabricating machine sold. Please, contact us today and ask how the quality of the machines we build will translate into quality coax assemblies on your shop floor.